- \n
- 3-stage filtration (pre-filter, activated carbon filter and RO membrane)<\/strong><\/li>\n
- Effective even at low water pressure (from 2.1 bar)<\/strong><\/li>\n
- Produces up to 12 litres of clean water per hour at 3 bar and 12\u00b0C<\/strong><\/li>\n
- Easy installation directly on existing tap<\/strong><\/li>\n
- Ideal for all types of beer brewing and precise water adjustment<\/strong><\/li>\n<\/ul>\n
Give your home brew the best start with the highest quality water. This RO system is the optimal choice for those who want to brew with maximum precision and flavour.<\/p>\n
Content:<\/h3>\n
- \n
- 1 tap adapter<\/li>\n
- 1 inline sediment filter 5\u00b5<\/li>\n
- 1 inline ball filter 5\u00b5<\/li>\n
- Osmosis membrane 75 GPD ULP - Ultra Low Pressure<\/li>\n
- 1 diaphragm housing and collet<\/li>\n
- 1 lige ud fitting m\/ pakning med 1\/2″ indvendig r\u00f8rgevind<\/li>\n
- 3 metre 1\/4\" plastic hose, 1 metre white, red and blue<\/li>\n
- 450ml restrictor<\/li>\n
- Brackets and screws for wall mounting<\/li>\n<\/ul>\n
<\/h2>\n
Extended User Guide<\/h2>\n
Installation<\/h3>\n
![\"Reverse](\"https:\/\/lundteknik.dk\/wp-content\/uploads\/2025\/05\/ro-samling-344x400.png\")
<\/p>\n- \n
- Location:<\/strong>\n
- \n
- Find a suitable location close to water connection and drainage.<\/li>\n
- Make sure the system is stable and upright.<\/li>\n<\/ul>\n<\/li>\n
- Assembly:<\/strong>\n
- \n
- Remove the blue lock and hose to the RO membrane housing<\/li>\n
- Install the RO membrane as shown in the picture and reinstall the hose.<\/li>\n
- Connect the water hose (white) to the system and the tap with the included adapter or tap connector.<\/li>\n
- Connect the waste water hose (red) and lead it to the drain or tank for garden watering etc.<\/li>\n
- Connect the RO water out hose (blue)<\/li>\n
- Replace all the little blue fuses.<\/li>\n
- The tap is used to adjust the ratio of spinning water to RO water.<\/li>\n<\/ul>\n<\/li>\n
- Density test:<\/strong>\n
- \n
- Slowly open the tap and check that all connections are tight.<\/li>\n
- Fix any leaks immediately.<\/li>\n<\/ul>\n<\/li>\n<\/ol>\n
Operation and use<\/h3>\n
- \n
- Start:<\/strong>\n
- \n
- Allow the system to run for at least 15 minutes on first use to clean the system.<\/li>\n
- Adjust the tap to about 1\/3 RO water<\/li>\n
- If you have a TDS meter, you can fine-tune the ratio between RO and spin water for optimal water utilisation.<\/li>\n
- Now collect the first RO water.<\/li>\n<\/ul>\n<\/li>\n
- Daily use:<\/strong>\n
- \n
- Leave the system running and collect the purified water in a clean, preferably sterile container.<\/li>\n
- The water is now ready to use in your beer brewing.<\/li>\n<\/ul>\n<\/li>\n
- Mineral customisation:<\/strong>\n
- \n
- Customise the mineral profile as needed with desired salts (e.g. calcium chloride, calcium sulphate, calcium carbonate or magnesium sulphate). See more under Water treatment<\/a><\/li>\n<\/ul>\n<\/li>\n<\/ol>\n
Maintenance<\/h3>\n
- \n
- Filter replacement:<\/strong>\n
- \n
- Sediment filter and carbon filter should be changed every 6-12 months depending on usage and water quality.<\/li>\n
- The RO membrane is typically replaced every 2-3 years or when efficiency drops noticeably.<\/li>\n<\/ul>\n<\/li>\n
- Regular cleaning:<\/strong>\n
- \n
- Flush the system with clean water if it has not been used for an extended period of time.<\/li>\n
- Store the system in a dry place when not in use to avoid bacterial growth.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n
Troubleshooting<\/h3>\n
- \n
- Low water production:<\/strong>\n
- \n
- Check the water pressure and temperature (ideally 2.1 bar and 12-20\u00b0C).<\/li>\n
- Check filters and membrane for clogging and replace if necessary.<\/li>\n<\/ul>\n<\/li>\n
- Leaky system:<\/strong>\n
- \n
- Check all fittings and gaskets and tighten or replace if necessary.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n
Following this extended guide will ensure optimal performance, longevity and the best quality of your brewing water.<\/p>","protected":false},"excerpt":{"rendered":"
3-stage reverse osmosis system<\/h1>\n
Perfect for home brewing. Ensures clean and neutral RO water for precise water adjustment and optimal flavour.<\/p>\n
- Check all fittings and gaskets and tighten or replace if necessary.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n
- Low water production:<\/strong>\n
- Filter replacement:<\/strong>\n
- Customise the mineral profile as needed with desired salts (e.g. calcium chloride, calcium sulphate, calcium carbonate or magnesium sulphate). See more under Water treatment<\/a><\/li>\n<\/ul>\n<\/li>\n<\/ol>\n
- Start:<\/strong>\n
- Location:<\/strong>\n
- Effective even at low water pressure (from 2.1 bar)<\/strong><\/li>\n